Introduction To 3G , UMTS, And Its Techniques

Introduction To 3G , UMTS, And Its Techniques

The Universal Mobile Telecommunications System (UMTS)

The Universal Mobile Telecommunications System (UMTS) is a third generation mobile cellular system for networks based on the GSM standard. Developed and maintained by the 3GPP (3rd Generation Partnership Project), UMTS is a component of the International Telecommunications Union IMT-2000 standard set and compares with the CDMA2000 standard set for networks based on the competing cdmaOne technology. UMTS uses wideband code division multiple access (W-CDMA) radio access technology to offer greater spectral efficiency and bandwidth to mobile network operators.UMTS specifies a complete network system, which includes the radio access network (UMTS Terrestrial Radio Access Network, or UTRAN), the core network (Mobile Application Part, or MAP) and the authentication of users via SIM (subscriber identity module) cards.The technology described in UMTS is sometimes also referred to as Freedom of Mobile Multimedia Access (FOMA) or 3GSM.Unlike EDGE (IMT Single-Carrier, based on GSM) and CDMA2000 (IMT Multi-Carrier), UMTS requires new base stations and new frequency allocations. UMTS supports maximum theoretical data transfer rates of 42 Mbit/s when HSPA+ is implemented in the network.[2] Users in deployed networks can expect a transfer rate of up to 384 kbit/s for Release '99 (R99) handsets (the original UMTS release), and 7.2 Mbit/s for HSDPA handsets in the downlink connection. These speeds are significantly faster than the 9.6 kbit/s of a single GSM error-corrected circuit switched data channel, multiple 9.6 kbit/s channels in HSCSD and 14.4 kbit/s for CDMAOne channels.Since 2006, UMTS networks in many countries have been or are in the process of being upgraded with High Speed Downlink Packet Access (HSDPA), sometimes known as 3.5G. Currently, HSDPA enables downlink transfer speeds of up to 21 Mbit/s. Work is also progressing on improving the uplink transfer speed with the High-Speed Uplink Packet Access (HSUPA). Longer term, the 3GPP Long Term Evolution (LTE) project plans to move UMTS to 4G speeds of 100 Mbit/s down and 50 Mbit/s up, using a next generation air interface technology based upon orthogonal frequency-division multiplexing.The first national consumer UMTS networks launched in 2002 with a heavy emphasis on telco-provided mobile applications such as mobile TV and video calling. The high data speeds of UMTS are now most often utilised for Internet access: experience in Japan and elsewhere has shown that user demand for video calls is not high, and telco-provided audio/video content has declined in popularity in favour of high-speed access to the World Wide Web—either directly on a handset or connected to a computer via Wi-Fi, Bluetooth or USB.

Technologies:-
UMTS combines three different air interfaces, GSM's Mobile Application Part (MAP) core, and the GSM family of speech codecs.

Air interfaces

UMTS provides several different terrestrial air interfaces, called UMTS Terrestrial Radio Access (UTRA).[3] All air interface options are part of ITU's IMT-2000. In the currently most popular variant for cellular mobile telephones, W-CDMA (IMT Direct Spread) is used.Please note that the terms W-CDMA, TD-CDMA and TD-SCDMA are misleading. While they suggest covering just a channel access method (namely a variant of CDMA), they are actually the common names for the whole air interface standards W-CDMA (UTRA-FDD) UMTS transmitter on the roof of a building W-CDMA uses the DS-CDMA channel access method with a pair of 5 MHz wide channels. In contrast, the competing CDMA2000 system uses one or more available 1.25 MHz channels for each direction of communication. W-CDMA systems are widely criticized for their large spectrum usage, which has delayed deployment in countries that acted relatively slowly in allocating new frequencies specifically for 3G services (such as the United States).

The specific frequency bands originally defined by the UMTS standard are 1885–2025 MHz for the mobile-to-base (uplink) and 2110–2200 MHz for the base-to-mobile (downlink). In the US, 1710–1755 MHz and 2110–2155 MHz are used instead, as the 1900 MHz band was already used.[5] While UMTS2100 is the most widely deployed UMTS band, some countries' UMTS operators use the 850 MHz and/or 1900 MHz bands (independently, meaning uplink and downlink are within the same band), notably in the US by AT&T Mobility, New Zealand by Telecom New Zealand on the XT Mobile Network and in Australia by Telstra on the Next G network. Some carriers such as T-Mobile use band numbers to identify the UMTS frequencies. For example, Band I (2100 MHz), Band IV (1700/2100 MHz), and Band V (850 MHz).

UTRA-TDD HCR

UMTS-TDD's air interfaces that use the TD-CDMA channel access technique are standardized as UTRA-TDD HCR, which uses increments of 5 MHz of spectrum, each slice divided into 10ms frames containing fifteen time slots (1500 per second).[6] The time slots (TS) are allocated in fixed percentage for downlink and uplink. TD-CDMA is used to multiplex streams from or to multiple transceivers. Unlike W-CDMA, it does not need separate frequency bands for up- and downstream, allowing deployment in tight frequency bands.

TD-CDMA is a part of IMT-2000 as IMT CDMA TDD.

TD-SCDMA (UTRA-TDD 1.28 Mcps low chip rate)

TD-SCDMA

TD-SCDMA uses the TDMA channel access method combined with an adaptive synchronous CDMA component[7] on 1.6 MHz slices of spectrum, allowing deployment in even tighter frequency bands than TD-CDMA. However, the main incentive for development of this Chinese-developed standard was avoiding or reducing the license fees that have to be paid to non-Chinese patent owners. Unlike the other air interfaces, TD-SCDMA was not part of UMTS from the beginning but has been added in Release 4 of the specification.

Radio access network UTRAN

UMTS also specifies the Universal Terrestrial Radio Access Network (UTRAN), which is composed of multiple base stations, possibly using different terrestrial air interface standards and frequency bands.

UMTS and GSM/EDGE can share a Core Network (CN), making UTRAN an alternative radio access network to GERAN (GSM/EDGE RAN), and allowing (mostly) transparent switching between the RANs according to available coverage and service needs. Because of that, UMTS's and GSM/EDGE's radio access networks are sometimes collectively referred to as UTRAN/GERAN.

UMTS networks are often combined with GSM/EDGE, the latter of which is also a part of IMT-2000.The UE (User Equipment) interface of the RAN (Radio Access Network) primarily consists of RRC (Radio Resource Control), RLC (Radio Link Control) and MAC (Media Access Control) protocols. RRC protocol handles connection establishment, measurements, radio bearer services, security and handover decisions. RLC protocol primarily divides into three Modes—Transparent Mode (TM), Unacknowledge Mode (UM), Acknowledge Mode (AM). The functionality of AM entity resembles TCP operation whereas UM operation resembles UDP operation. In TM mode, data will be sent to lower layers without adding any header to SDU of higher layers. MAC handles the scheduling of data on air interface depending on higher layer (RRC) configured parameters The set of properties related to data transmission is called Radio Bearer (RB). This set of properties decides the maximum allowed data in a TTI (Transmission Time Interval). RB includes RLC information and RB mapping. RB mapping decides the mapping between RB<->logical channel<->transport channel. Signaling messages are sent on Signaling Radio Bearers (SRBs) and data packets (either CS or PS) are sent on data RBs. RRC and NAS messages go on SRBs. Security includes two procedures: integrity and ciphering. Integrity validates the resource of messages and also makes sure that no one (third/unknown party) on the radio interface has modified the messages. Ciphering ensures that no one listens to your data on the air interface. Both integrity and ciphering are applied for SRBs whereas only ciphering is applied for data RBs

Core network:-

Mobile Application

With Mobile Application Part, UMTS uses the same core network standard as GSM/EDGE. This allows a simple migration for existing GSM operators. However, the migration path to UMTS is still costly: while much of the core infrastructure is shared with GSM, the cost of obtaining new spectrum licenses and overlaying UMTS at existing towers is high.The CN can be connected to various backbone networks, such as the Internet or an Integrated Services Digital Network (ISDN) telephone network. UMTS (and GERAN) include the three lowest layers of OSI model. The network layer (OSI 3) includes the Radio Resource Management protocol (RRM) that manages the bearer channels between the mobile terminals and the fixed network, including the handovers.

UMTS frequency bands

Over 130 licenses have already been awarded to operators worldwide (as of December 2004), specifying W-CDMA radio access technology that builds on GSM. In Europe, the license process occurred at the tail end of the technology bubble, and the auction mechanisms for allocation set up in some countries resulted in some extremely high prices being paid for the original 2100 MHz licenses, notably in the UK and Germany. In Germany, bidders paid a total €50.8 billion for six licenses, two of which were subsequently abandoned and written off by their purchasers (Mobilcom and the Sonera/Telefonica consortium). It has been suggested that these huge license fees have the character of a very large tax paid on future income expected many years down the road. In any event, the high prices paid put some European telecom operators close to bankruptcy (most notably KPN). Over the last few years some operators have written off some or all of the license costs. Between 2007 and 2009, all three Finnish carriers begun to use 900 MHz UMTS in a shared arrangement with its surrounding 2G GSM base stations for rural area coverage, a trend that is expected to expand over Europe in the next 1–3 years.

The 2100 MHz band (downlink around 2100 MHz and uplink around 1900 MHz) allocated for UMTS in Europe and most of Asia is already used in North America. The 1900 MHz range is used for 2G (PCS) services, and 2100 MHz range is used for satellite communications. Regulators have, however, freed up some of the 2100 MHz range for 3G services, together with a different range around 1700 MHz for the uplink.

AT&T Wireless launched UMTS services in the United States by the end of 2004 strictly using the existing 1900 MHz spectrum allocated for 2G PCS services. Cingular acquired AT&T Wireless in 2004 and has since then launched UMTS in select US cities. Cingular renamed itself AT&T Mobility and is rolling out[citation needed] some cities with a UMTS network at 850 MHz to enhance its existing UMTS network at 1900 MHz and now offers subscribers a number of dual-band UMTS 850/1900 phones.T-Mobile's rollout of UMTS in the US focused on the 1700 MHz band.

In Canada, UMTS coverage is being provided on the 850 MHz and 1900 MHz bands on the Rogers and Bell-Telus networks. Bell and Telus share the network. Recently, new providers Wind Mobile, Mobilicity and Videotron have begun operations in the 1700 MHz band.

In 2008, Australian telco Telstra replaced its existing CDMA network with a national UMTS-based 3G network, branded as NextG, operating in the 850 MHz band. Telstra currently provides UMTS service on this network, and also on the 2100 MHz UMTS network, through a co-ownership of the owning and administrating company 3GIS. This company is also co-owned by Hutchison 3G Australia, and this is the primary network used by their customers. Optus is currently rolling out a 3G network operating on the 2100 MHz band in cities and most large towns, and the 900 MHz band in regional areas. Vodafone is also building a 3G network using the 900 MHz band.

UMTS phones (and data cards) are highly portable—they have been designed to roam easily onto other UMTS networks (if the providers have roaming agreements in place). In addition, almost all UMTS phones are UMTS/GSM dual-mode devices, so if a UMTS phone travels outside of UMTS coverage during a call the call may be transparently handed off to available GSM coverage. Roaming charges are usually significantly higher than regular usage charges.

Most UMTS licensees consider ubiquitous, transparent global roaming an important issue. To enable a high degree of interoperability, UMTS phones usually support several different frequencies in addition to their GSM fallback. Different countries support different UMTS frequency bands – Europe initially used 2100 MHz while the most carriers in the USA use 850 MHz and 1900 MHz. T-Mobile has launched a network in the US operating at 1700 MHz (uplink) /2100 MHz (downlink),

and these bands are also being adopted elsewhere in the Americas. A UMTS phone and network must support a common frequency to work together. Because of the frequencies used, early models of UMTS phones designated for the United States will likely not be operable elsewhere and vice versa. There are now 11 different frequency combinations used around the world—including frequencies formerly used solely for 2G services.

UMTS phones can use a Universal Subscriber Identity Module, USIM (based on GSM's SIM) and also work (including UMTS services) with GSM SIM cards. This is a global standard of identification, and enables a network to identify and authenticate the (U)SIM in the phone. Roaming agreements between networks allow for calls to a customer to be redirected to them while roaming and determine the services (and prices) available to the user. In addition to user subscriber information and authentication information, the (U)SIM provides storage space for phone book contact. Handsets can store their data on their own memory or on the (U)SIM card (which is usually more limited in its phone book contact information). A (U)SIM can be moved to another UMTS or GSM phone, and the phone will take on the user details of the (U)SIM, meaning it is the (U)SIM (not the phone) which determines the phone number of the phone and the billing for calls made from the phone.

Japan was the first country to adopt 3G technologies, and since they had not used GSM previously they had no need to build GSM compatibility into their handsets and their 3G handsets were smaller than those available elsewhere. In 2002, NTT DoCoMo's FOMA 3G network was the first commercial UMTS network—using a pre-release specification,[8] it was initially incompatible with the UMTS standard at the radio level but used standard USIM cards, meaning USIM card based roaming was possible (transferring the USIM card into a UMTS or GSM phone when travelling). Both NTT DoCoMo and SoftBank Mobile (which launched 3G in December 2002) now use standard UMTS.

Introduction To 3G , UMTS, And Its Techniques