NEMO Outdoor Training Tutorial ( 3g wcdma & 4g LTE )

NEMO Outdoor Training Tutorial

Software

Nemo Outdoor/Indoor Installation

·       You need to have local Administrator rights to install Nemo Outdoor.

·       Run the Nemo Outdoor setup.exe file and follow the instructions. Current Nemo Outdoor SW is 4.20.73  Check the latest versions of Nemo software from our web pages at (www.nemotechnologies.com) Valid to users with Technical Support Agreement only.

·       Install DKU 2 cable driver.

·       Restart laptop.

• LINK:- Complete Article NEMO OUTDOOR Training & Drive Test Case Study

Hardware

Testing Concept – Voice Call

 The voice testing environment consists of

-        Nemo Outdoor compatible test measurement mobiles.

-        Laptop/Tablet PC with Nemo Outdoor installed.

-        Necessary connecting cables .

-        GPS receiver for Outdoor measurement.

-        (optional) fast frequency scanner.

NEMO OUTDOOR

Testing Concept – PS Data Call

ü  The PS data testing environment consists of Nemo Outdoor Application Server(e.g. FTP server, HTTP server, POP3 server, SMTP server, or WAP server)

NEMO Outedoor Equiptments

Nemo Outdoor Measurement Configuration

Manual / Automated Mode

·       Nemo Outdoor supports manual and automated mode.

       1.     Manual mode

·       Is based on the user establishing a data transfer connection or making voice calls.

ü  This mode is useful, when user wants to make a single continuous data transfer session or a voice call to monitor the resource allocation and cell reselection performance.

ü  This mode requires the user to control phones with Nemo Outdoor. The user should NOT use the mobile keyboard to establish voice calls or data calls.

     2.     Automated mode

·       Is based on scripts that establish data transfer connections or voice calls on behalf of the user and can repeat the same or different sessions for a defined period of time. Scripts can be saved and edited. Script files can be, quickly and easily built with the Script Editor.

Introduction to Graphical User Interface

• LINK:- Real Time Drive Test & 3G Optimization CASE STUDY
• LINK:- Nemo Outdoor Graphical User Interface

Introduction to Graphical User Interface

NEMO OUTDOOR Manual Measurement Configuration

NEMO OUTDOOR Manual Measurement

 Configuration:-

·       Information on this tab should be filled in when doing Manual Measurement. (Press “Properties”)

·       Voice Number defines the phone number to which voice calls will be made.

·       Data Number defines the phone number for data calls, user name and password for service, etc.

·       PDP Context Properties defines used APN for Packet data connection

·       Data Protocol defines whether FTP or UDP is used for data transfer

·       ICMP Ping Properties defines Ping settings, like Ping address and size of Ping data

Manual Measurement Control

NEMO OUTDOOR Manual Measurement

·       Measurement can be done from Mobile’s Control Panel or from Measurement menu by selecting the appropriate mobile

NEMO OUTDOOR Manual Measurement

Automatic Measurement

·       Measurements can be automatically repeated by predefined number of times

·       Voice calls, data calls, attach, PDP activation, FTP, Web browsing, SMS, MMS, launch of external application, Ping sessions, etc. can be included in automatic measurement sequence

·       Add / Modify / Delete / Move up / Move down / Append script / Repeat script value/ New /Open / Save / Save As...

NEMO Outdoor Automatic Measurement

Voice Call Script Configuration

1.     Script Editor/ Add / Voice Call

2.     Voice Call Properties

-        Number defines the number to be called

-        Call Duration determines the time that the call lasts in seconds

-        Call Attempt Timeout value determines the maximum duration of the call attempt. After that, the call attempt is considered to be failed.

• LINK:- 3G Rf Optimization & Log File Analysis
• LINK:-3G Antenna Principle For Telecom

NEMO Outdoor Voice Calss Script

》》CLICK HERE《《FOR THE NEMO OUTDOOR GRAPHICAL USER INTERFACE》》CLICK HERE《《

PS Script Configuration

-        Access Point Name defines the APN used   

-        User Name/Password etc. Depend on operator’s settings

NEMO Outdoor PS Script Configuration

·       Host Name: IP address of the FTP server used.

·       Username: username for the FTP server.

·       Password: password for the FTP server.

·       Passive Mode: Some firewalls may be configured to refuse any incoming connection requests, and in that case the data transfer would fail. With passive mode, the client always opens those new connections so the firewall does not block the connection.

·       Direction: Receive – downloading; Send – uploading

·       Remote File: File @ FTP Server

·       Local File: File @ Testing laptop

·        URL: IP address of the test file that will be downloaded. For example, 203.125.58.120/1000kb.htm

·        Local File: File @ Testing laptop

Script Configuration

·       Editing PS Script

-        Ping Test

-        The ICMP (Internet Control Message Protocol) Ping functionality allows you to perform ping measurements simultaneously with FTP testing and data transfers.

Script Configuration

Script Enhancements

·       Possibility to synchronize scripts repeats between devices for benchmarking measurements.

·       Improved wait function allows waiting for notifications during script measurements.

·       Option to use measurement settings configured for manual testing during script measurements.

NEMO Script Configuration

》》CLICK HERE《《FOR THE NEMO OUTDOOR GRAPHICAL USER INTERFACE》》CLICK HERE《《

Event Trigger Notifications

·       By clicking the Notifications sheet, you can access the Notifications dialog box

·       Select the Events that you would like to be notified of and also select whether the notification will be a textual note in the Output window, a sound (.wav file), or a bitmap

·       Own notifications can be created for different situations, like bad quality example below, in Configuration tool

NEMO Outrdoor Event  Trigger

User Defined Event Trigger Configuration 1

User Defined Event Trigger Configuration 2

Event Trigger Configuration

 ·       Event bitmap displayed in map window

·       Event bitmap displayed in line graph

(1.) Textual Notification displayed in the Output window

(2.) Sound Notification

(1.) Textual Notification displayed in the Output window

Real-time monitoring during measurement

Real-time monitoring during measurement

Real-time monitoring during measurement

General User Interface Configuration

General User Interface Configuration

General User Interface Configuration

•        automatic file name generation

•        manual file name generation

•        prefix (for file name)

•        force idle mode when stopping scripts

•        start scripts automatically

•        use time from GPS

•        wait for GPS fix before starting

•        measurement

>>Click Here<<For Drive Test Case Study>>Click Here<<

》》CLICK HERE《《FOR THE GRAPHICAL USER INTERFACE》》click here《《

-----------------------------------------------------------------------------------------------------------------
("23,899 Subscriber's Viewed Articles")

• LINK:- Telecom Interview Questions n Answers ( Important Article )
• LINK:-  3G Rf-Optimization & Planning Interview Questions Answers
• LINK:- 3G Rf Planning Procedure ( FULL ARTICLE )
• LINK:- 3G Radio Wave Propagation ( FULL ARTICLE )